U312 Automatic Nozzle

U312 Automatic Nozzle

U312 series automatic nozzles are designed with today's customer in mind. Small, trim, light weight, easy and convenient to operate, the is a rugged performer that offers long life and reliable service.

Warning

Use foreign objects to hold open automatic nozzles could result in failure to shut-off and personal injury.

Materials:

Body: Aluminum

seals: Buna-N, Viton

Main stem seals: Viton Cased Oil Seal / Graphite with Teflon

Main stem: Stainless steel

Color of insulator :

Red Green Blue Yellow Black

Features :

U312-B/D/F Flow rate: 0-60 L/m (15/16")

U312-A/C/E Flow rate: 0-45 L/m (13/16")

Working Pressure: 0.18Mpa

U312 Automatic Nozzles-or diesel, kerosene and all kinds of gasoline service

Easily replaced spout- simply remove the screw.

Spout kits are available from HONGYANG.

Low profile aluminum body- light weight, easier to handle, provides an attractive, image enhancing appearance.

Hold-open rack is available for full service applications.

The one hand control means easy setting to flow rate for customer's convenience.

Full hand insulator- protects both nozzle and vehicle, and insulates users' hands.

Vacuum Design: Side-Sealing Design.

Selective casting process of body- low-pressure casting technique or high-pressure casting technique.

The high-pressure casting technique can reduce diesel foaming and static electricity.

100% Factory Tested.

Available Colors- color chart on inside back cover Selective splash guard.

Replacement Parts:

Key Description

1 Spout 13/16" & Spout 15/16"

2 Full hand insulator

3 Main Valve Assembly

4 Lever

5 Ratchet Pin

6 Diaphragm assembly

Package:

Net Weight Cross Weight Dimension

18.75kg/case of 15

12.25kg/case of 10 22kg/case of 15

15kg/case of 10 55x34x42.5cm/case of 15

37.5x34x43cm/case of 10

Important:

The products should be used in compliance with applicable country, province and local Laws and regulations. Products selection should be based on physical Specifications and limitations and compatibility with the environmentand materials to be handled. HONGYANG makes no warranty of fitness for a particular use. All illustrations and Specifications in this literature are based on the latest products information available at the time of publication,HONGYANG reserves the right to make changes at any time in price, materials. Specifications and models and to discontinue models without notice or obligation.

� fuel dispenser �t shut. Check valve can’t open fully as amount of waste at the lower part of outlet valve of vapor separator. Upper cover gasket of vapor separator is broken, leads to pressure no fuel dispenser t enough. 3.5. Pipeline is jammed and bottom valve could not fully open. Serious fluctuation and noise in operation Jammed filter net and too long or fuel dispenser too thin pipeline cause heavy loan making big noise. Locked overflow valve or too tight adjusting bolt. Jammed vane causes serious oil fluctuation Pipeline vibrates heavy. Delivery frequency is same to inherent mechanical frequency. instable flow rate as starting Overflow valve works abnormally. Pipeline has U shape curve, generating air resistance. Pipe valve has some trouble. Contain foam in flowing oil Pipe and bottom valve trouble because of ceaseless exhausting air in vapor separator. Exhausting pipe inhales air. Inspect check valve and cone-shaped valve. Vapor separator’s outlet valve and exhausting valve is jammed leading to fail to separate air from oil. Accuracy beyond scope Double optical board is broken in pulse sensor, which leads to countable pulse lost. Inner leakage in measurement transducer causes accuracy beyond range. Change new transducer. As insufficient capacity of vapor separator, check outlet valve and exhausting pipe. Fuel dispenser’s main board is broken, which also lead to inaccuracy. Pipeline leakage causes vapor separator lost function. Motor rotates slowly and become hot as refueling Motor has been destroyed. Winding short circuit or disconnected; starting capacitor has been damaged in single phase motor; Control circuit of motor is broken, which leads to starting problem. Exterior wiring also cause motor failure, (absent electric phase, long wiring distance, too thin lead, much lower voltage) Oil overflowing in exhausting pipe Small floater is damaged and dropped down in vapor separator. Large amount of oil flow into vapor separating chamber; oil is discharge from exhausting pipe as return valve trouble

f fuel dispenser or mixed neutron　　sections of methane propane and dimethyl　　 photon radiation fields　　ether　　 fuel dispenser Measurements of neutron spectra on high-　　Energy-selective Faraday cup for the meas-　　 fuel dispenser energy heavy-ion accelerators of the GSI in　　urement of the total electron scattering cross　　 Darmstadt　　sections in gases　　 Investigation of measuring procedures for　　Generation of ionization clusters in　　 individual dosimetry at workplaces with　　nanometric volumes by particles　　 mixed neutronphoton radiation　　 109　　Ionizing Radiation　　International affairs　　Metrological equivalence between state insti-　　tutes for activity measurements　　The Radon Intercomparison 2001 to 2002 and　　the extension to the EUROMET Supplemen-　　tary Comparison　　International intercomparison for the realiza-　　tion of the activity concentration of　　radionuclides in ground-level air　　Evaluation of the comparison measurement　　CCRI(III)-K.10　　Further information　　Charge measuring device for the operation of　　ionization chambers　　 110　　 Ionizing Radiation　　111　　Ionizing Radiation　　 112　　 Reports from the Divisions　　Temperature　　and　　Synchrotron Radiation　　 Division　　 7　　 113　　Temperature　　Synchrotron　　Berlin Institute　　In its lecture-hall at the Hermann von Helm-　　holtz Building the PTB celebrated on Septem-　　ber 26 the 50th anniver

m fuel dispenser essage through the media by issuing a one-way press release, but that s as flawed right now as a 15 or 30-second TV ad,�? says Pam Talbot, Edelman s chief in America. The fragmen fuel dispenser tation of media has seen an explosion in the number of ways people seek news and entertainment, with many turning to websites, cable TV, satellite radio an fuel dispenser d podcasts. Yet a consequence of the proliferation of media is that original content becomes even more sought after. Hence crisply written or well-produced PR material can more easily get an airing. Media commentators have noted how PR material is now being published by some local newspapers virtually unedited and unchecked. Some branches of journalism have come to depend on a drip- feed of information and products from the PR industry. Journalists focusing on electronics, fashion, travel, beauty and food have a huge appetite for free samples. Gossip about celebrities is also largely mediated by the PR industry. Never shy about accentuating the positive, the PR industry might be expected to be trumpeting its rise. And there is indeed some triumphalism (and spin) around. Al and Laura Ries, a father and daughter team of marketing consultants, have written a book entitled “The Fall of Advertising & the Rise of PR�? “PR has credibility,�?they assert “Advertising does not.�?Their advice is that a marketing campaign should start with publicity and shift to advertising only after the PR objectives have been achieved. Some PR firms see an opportunity to move up their clients hierarchy—becoming not just service providers, but also purveyors of strategic advice to senior management. But even within the industry, there are sceptics. Dorothy Crenshaw, president of Stanton Crenshaw, an independent PR firm based in New York, says that many of her colleagues are suffering from “consultant envy”�? but that PR remains a very inexact science. There are also limits to the miracles it can be expected to achieve. She claims to have turned down a $1m commissi